Table of Content
Please note that this limited warranty applies only when the product is used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use). The manufacturer cannot guarantee results as it has no control over surface and sub-surface preparation and product application. (Proper installation of pavers or slabs to ensure long-term stability of work, including granular foundation of certified crushed stone of 0-3/4″ (0-20 mm) (minimum of 6″ ), bedding sand layer (maximum of 1″ ) and appropriate installation of reinforced edging in accordance with above specified method for applying product.) Also warranted when used with Gator Base.
When the pavers are installed directly on aggregates with large voids. C. Never allow paved surface to dry out during the water-activation phase. B. Never allow paved surface to dry out during the water-activation phase. At least 1/8″ below top of paver’s surface or 1/8″ below the chamfer. C-33 sand or ASTM No. 9 stone can be used under pavers.
IMPORTANT INSTALLATION NOTES
Pavers must be completely dry before installing a minimum of 1 1/2″ deep into the joints. Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints. Available in Beige, Slate Grey, Ivory and Black Diamond. Watering must be started at the lowest point of the paved surface. Available in Nevada Tan, Oxford Grey, Ivory White and Jet Black. Installation steps 1 to 4 for a new paver surface.
All pavers must be completely interlocked for vehicular and pedestrian use. If pavers are fanned they are not considered interlocked. B. Watering must be started at the lowest point of the paved surface. Repels the water and the water starts to accumulate on the joints.
Overlay application:
Moss, mold and mildew are caused by certain on-site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product. Please note that when the product is used for other purposes (Mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from purchase. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of any Gator Polymeric Sand for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10. Be careful not to disturb the bedding material under the pavers. Pavers must be completely dry before installing a minimum of 1 1/2’’ deep into the joints. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of any Polymeric Sand for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10.
Level, must be at least 1/8″ below top of paver’s surface or 1/8″ below the chamfer or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tire.For textured or pre-finished surfaces, we recommend to remove all the sand from the paver or slab surface prior to using the plate or roller compactor. Is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a traditional base system composed of 2 layers. The upper layer can have a maximum of 1″ of bedding sand. The lower layer must have a minimum of 6″ of crushed stone compacted at 98% Proctor density.
(For a new paver surface)
However, for a period of 15 years from purchase, the manufacturer agrees that if the product is proven to be defective, and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above, then the manufacturer agrees to refund the purchase price. The presence of moss, mold or mildew is caused by the particular on-site conditions, including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product after installation. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of GATOR MAXX G2 for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of GATOR SUPERSAND G2 for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of POLYBIND SAND G2 for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of POLYBIND COMPLETE SAND G2 for any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2 and #10.
Gator Maxx Sand is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements etc. The concrete pavers must be installed on a traditional or overlay base system. When maintaining the paver surface, apply Gator Shampoo to clean the entire paved surface including the paver joints. Wash, rinse and remove any residue by using a hose and a watering gun set to shower with the normal maximum water pressure from any residential or commercial building (typically 80 psi/550 kPa). Will not cause nor prevent moss, mold or mildew.
Traditional base system:
For textured or pre-finished surfaces, we recommend to remove all the sand from the paver or slab surface prior to using the plate or roller compactor. Gator Maxx Sandis a unique mixture of polymer binders and calibrated sand. The installation of Gator Maxx Sandis almost identical to using regular paver joint sand except for the application of water. Once Gator Maxx Sand sets, it becomes very firm and locks between the paver joints while still retaining flexibility and providing a long lasting, durable jointing material.
